12V DC to 220V AC Converter [Tested Circuit]

Table of Contents

In this tutorial blog, we will look into the circuit architecture to convert 12V DC to 220V AC power. This is a tested circuit so you will have no problem in trying it out yourself.

Basic Introduction

Inverters are often needed at places where it is not possible to get AC supply from the Mains. An inverter circuit is used to convert the DC power to AC power. Inverters can be of two types True/pure sine wave inverters and quasi or modified inverters. These true /pure sine wave inverters are costly ,while modified or quasi inverters are inexpensive.

These modified inverters produce a square wave and these are not used to power delicate electronic equipment. Here, a simple voltage driven inverter circuit using power transistors as switching devices is build, which converts 12V DC signal to single phase 220V AC.

Principle Behind this Circuit

The basic idea behind every inverter circuit is to produce oscillations using the given DC and apply these oscillations across the primary of the transformer by amplifying the current. This primary voltage is then stepped up to a higher voltage depending upon the number of turns in primary and secondary coils.

Inverter circuit Using Transistors

Inverter output

A 12V DC to 220 V AC converter can also be designed using simple transistors. It can be used to power lamps up to 35W but can be made to drive more powerful loads by adding more MOSFETS.

The inverter implemented in this circuit is a square wave inverter and works with devices that do not require pure sine wave AC.

Circuit Diagram for 12V DC to 220V AC Converter 

12v to 220v inverter cirucit

Inverter Circuit

Components required

The component required to execute this project are given below –

  • 12v Battery
  • MOSFET IRF 630 -2
  • 2N2222 Transistors
  • 2.2uf capacitors-2
  • Resistor
    • 680 ohm-2
    • 12k-2
  • 12v-220v center tapped step up transformer.

Working of 12V DC to 220V AC Converter Circuit

The circuit can be divided into three parts: oscillator, amplifier and transformer. A 50Hz oscillator is required as the frequency of AC supply is 50Hz.

This can be achieved by constructing an Astable multivibrator which produces a square wave at 50Hz. In the circuit, R1, R2, R3, R4, C1, C2, T2 and T3 form the oscillator.

Each transistor produces inverting square waves. The values of R1, R2 and C1 (R4, R3 and C2 are identical) will decide the frequency. The formula for the frequency of square wave generated by the astable multivibrator is

F = 1/(1.38*R2*C1)

The inverting signals from the oscillator are amplified by the Power MOSFETS T1 and T4. These amplified signals are given to the step-up transformer with its center tap connected to 12V DC.

Output Reference Video

The turns ratio of the transformer must be 1:19 in order to convert 12V to 220V. The transformer combines both the inverting signals to generate a 220V alternating square wave output.

By using a 24V battery, loads up to 85W can be powered, but the design is inefficient. In order to increase the capacity of the inverter, the number of MOSFETS must be increased.

To design a 100 watt Inverter read  Simple 100 Watt inverter

12v DC to 220v AC Converter Circuit Using Astable Multivibrator

Inverter circuits can either use thyristors as switching devices or transistors.  Normally for low and medium power applications, power transistors are used. The reason for using power transistor is they have very low output impedance, allowing maximum current to flow at the output.

One of the important applications of a transistor is in switching.  For this application, the transistor is biased in saturation and cut-off region.

When the transistor is biased in saturation region, both the collector emitter and collector base junctions are forward biased. Here the collector emitter voltage is minimum and collector current is maximum.

Another important aspect of this circuit is the oscillator. An important use of 555 Timer IC is in its use as an astable multivibrator.

An astable multivibrator produces an output signal which switches between the two states and hence can be used as an oscillator. The frequency of oscillation is determined by the values of capacitor and resistors.

 Circuit Diagram

Circuit Diagram of 12v DC to 220v AC Converter

Circuit Diagram of 12v DC to 220v AC Converter – ElectronicsHub.Org

Circuit Components

  • V1 = 12V
  • R1 = 10K
  • R2 = 150K
  • R3 = 10Ohms
  • R4 = 10Ohms
  • Q1 = TIP41
  • Q2 = TIP42
  • D1 = D2 = 1N4007
  • C3 = 2200uF
  • T1 = 12V/220V step up transformer

Circuit Design Explanation

Oscillator Design:An astable multivibrator can be used as an oscillator. Here an astable multivibrator using 555 timer is designed. We know, frequency of oscillations for a 555 timer in astable mode is given by:

f = 1.44/(R1+2*R2)*C

where R1 is the resistance between discharge pin and Vcc, R2 is the resistance between discharge pin and threshold pin and C is capacitance between threshold pin and ground.  Also the duty cycle of the output signal is given by:

D = (R1+R2)/(R1+2*R2)

Since our requirement is f =50Hz and D = 50% and assuming C to be 0.1uF, we can calculate the values of R1 and R2 to be 10K and 140K Ohms respectively. Here we prefer using a 150K potentiometer to fine tune the output signal.

Also a ceramic capacitor of 0.01uF is used between the control pin and ground.

Switching Circuit Design:Our main aim is to develop an AC signal of 220V. This requires use of high power transistors to allow the flow of maximum amount of current to the load. For this reason we use a power transistor TIP41 with a maximum collector current of 6A, where the base current is given by the collector current divided by the DC current gain.  This gives a bias current of about 0.4A *10, i.e.4A. However since this current is more than the maximum base current of the transistor, we prefer a value less than the maximum base current. Let us assume the bias current to be 1A. The bias resistor is then given by

R= (Vcc – VBE(ON))/Ibias

For each transistor, the VBE(ON) is about 2V. Thus Rb for each is calculated to be 10 Ohms. Since the diodes are used for biasing, the forward voltage drop across the diodes should be equal to the forward voltage drops across the transistors. For this reason, diodes 1N4007 are used.

The design considerations for both the PNP and NPN transistors are same. We are using a PNP power transistor TIP42.

Output Load Design: Since the output from the switching circuit is a pulse width modulated output, it might contain harmonic frequencies other than the fundamental AC frequency. For this reason, an electrolyte capacitor needs to be used to allow only the fundamental frequency to pass through it. Here we use an electrolyte capacitor of 2200uF, large enough to filter out the harmonics. Since it is required to get 220V output, it is preferred to use a step up transformer. Here a 12V/220V step up transformer is used.

12v DC to 220v AC Converter Circuit Operation

  • When this device is powered using the 12V battery, the 555 timer connected in astable mode produces square wave signal of 50Hz frequency.
  • When the output is at logic high level, diode D2 will conduct and the current will pass through diode D1, R3 to the base of transistor Q1.
  • Thus transistor Q1 will be switched on. When the output is at logic low level, diode D1 will conduct and current will flow via and D1 and R4 to the base of Q2, causing it to be switched on.
  • This allows the DC voltage to be produced across the primary of the transformer at alternate intervals. The capacitor ensures that the frequency of the signal is at the required fundamental frequency.
  • This 12V AC signal across the primary of the transformer is then stepped up to 220V AC signal across the transformer secondary.

Applications of 12v DC to 220v AC Converter Circuit

  1. This circuit can be used in cars and other vehicles to charge small batteries.
  2. This circuit can be used to drive low power AC motors
  3. It can be used in solar power system.


  1. Since 555 Timer is used, the output may slightly vary around the required duty cycle of 50%, i.e. exact 50% duty cycle signal is hard to achieve.
  2. Use of transistors reduces the efficiency of the circuit.
  3. Use of switching transistors has the possibility of causing cross over distortion in the output signal. However this limitation has been reduced to some extent by the use of biasing diodes.

Note – Instead of 555 timer one can use any astable multivibrator. For example this circuits can also be build using 4047 astable multivibrator,whose output current is amplified and applied to the transformer.



Similar Articles & Blogs

Explore similar articles on various electronics and electrical topics – 


We saw in the previous tutorial about the binary weighted digital-to-analogue converter that the analogue output voltage is the weighted sum of the individual inputs, and that

Learn More >>

Analogue to Digital Converter

Analogue-to-Digital Converters, (ADCs) allow micro-processor controlled circuits, Arduinos, Raspberry Pi, and other such digital logic circuits to communicate with the real world. In the real

Learn More >>

Transmission Gate

The analogue switch is a solid-state semiconductor switch that controls the transmission path of analogue signals. The open and closed operations of the switch positions

Learn More >>

Binary Adder

Another common and very useful combinational logic circuit which can be constructed using just a few basic logic gates allowing it to add together two

Learn More >>

Bus Transceiver

A Transceiver can be used to provide bidirectional, input or output control, of either digital or analogue devices to a common shared data bus. Unlike the buffer,

Learn More >>

Digital Comparator

Digital or Binary Comparators are made up from standard AND, NOR and NOT gates that compare the digital signals present at their input terminals and produce an output depending upon

Learn More >>