nRF24L01 Transceiver Module

Table of Contents

In this Arduino project, we will learn about the nRF24L01 Transceiver Module, its features, specifications and finally how to enable Arduino Wireless Communication using the nRF24L01 Transceiver Module.


Almost all the communication in the World today is wireless (at least from the end user perspective). You can find some sort of wireless communication in a variety of applications like TV Remotes, Mobile Phones, Computers, Toys, Cars, etc.

I don’t want to go into the details of Wireless Communication but you can find related information here: WIRELESS COMMUNICATION: INTRODUCTION, TYPES AND APPLICATIONS.

We have already seen a few wireless communication based projects in Electronics Hub, which are implemented using different technologies like Bluetooth, Infrared, RF (Radio Frequency) and WiFi (IEEE 802.11).


But in this project, I will be implementing an RF based Wireless Communication project using the nRF24L01 Transceiver IC. If you recall, I have implemented RF Communication in few earlier projects using the 434MHz RF Transmitter and Receiver Modules.

RF Transmitter Receiver

The main difference between these two RF Modules is their operating frequency. The nRF24L01 uses a 2.4GHz RF frequency whereas the earlier RF Modules used 434MHz RF frequency.

There is another important difference between them: in the 434MHz RF Modules, we have two separate modules; one for Transmission (Transmitter) and the other for Reception (Receiver). But the nRF24L0 is a Transceiver IC i.e. both the transmitter and receiver are integrated on the same IC.

A Brief Note on nRF24L01 Transceiver IC

The nRF24L01 is a single chip RF Transceiver IC developed by Nordic Semiconductor. It operates in the license-free 2.4GHz ISM band (ISM – Industrial, Scientific and Medical) with support for data rates of 250kbps, 1Mbps and 2Mbps.

For data rates of 250kbps and 1Mbps, the channel bandwidth is approximately 1MHz. So, taking the minimum and maximum operating frequencies of 2400MHz and 2525MHz, you can implement a maximum of 126 RF Channels if your data rate is limited to 250kbps or 1Mbps.

In 2Mbps data rate mote, the RF channel bandwidth should be 2MHz or more to ensure non-overlapping.

nRF24L01 Transceiver Module RF Channels

There is a special feature called MultiCeiver in nRF24L01 IC. This feature enables each RF Channel with a set of 6 unique addressed data pipes so that each module can communicate with 6 other modules in the same RF Channel.

Coming to the implementation of nRF24L01 IC, all you need is a 16MHz Crystal Oscillator, its supporting circuitry and an antenna. To design a Wireless Communication system using nRF24L01 Module, all you need is a Microcontroller, which is interfaced through Serial Peripheral Interface (SPI).

Important Features of nRF24L01 IC

  • Ultra-low power operation (26μA Standby-I mode, 900nA power down mode)
  • SPI Interface with Microcontroller
  • Integrated RF Transmitter, Receiver and Synthesizer
  • Operating voltage is 1.9V – 3.6V
  • Input pins can tolerate 5V

For more information on nRF24L01, please refer to the datasheet.

nRF24L01 Transceiver Module

Using the nRF24L01 IC, several manufacturers started developing the nRF24L0 Transceiver Module boards that contain the necessary components and pins for implementing a radio system.

The nRF24L01 Transceiver Module boards usually consists of the nRF24L01 Transceiver IC, a 16 MHz Crystal, an Antenna Trace (on the PCB), Pins for communication and power and a few passive components.

Following is the image of a typical nRF24L01 Transceiver Module board available today.

nRF24L01 Transceiver Module

IMPORTANT NOTE: The above module and almost all the latest nRF24L01 Transceiver Modules uses nRF24L01+ IC. It is an advanced version of the nRF24L01 IC and in fact, all the discussion made is the previous section is about nRF24L01+ IC.

Components on nRF24L01 Transceiver Module

The following image shows the components on a nRF24L01 Transceiver Module board.

Pins Configuration of nRF24L01 Transceiver Module

Coming to the pin configuration of the nRF24L01 Transceiver Module, it has 8 pins. They are VCC, GND, MOSI, MISO, SCK, IRQ, CE and CSN.

  • VCC: Power Supply Pin. Only 3.3V must be given.
  • GND: GND pin of the power supply.
  • SCK: SPI Clock Pin.
  • MOSI: SPI Slave Data Input Pin.
  • MISO: SPI Slave Data Output Pin.
  • IRQ: Active LOW Interrupt Pin.
  • CE: Chip Enable Pin.
  • CSN: SPI Chip Select Pin.

nRF24L01 Transceiver Module Pins

Interfacing nRF24L01 Transceiver Module with Arduino

As mentioned earlier, the nRF24L01 Transceiver Module communicates over SPI Interface. So, in order to interface an nRF24L01 Transceiver Module with Arduino, you need to use the SPI Pins of the Arduino board.

Since the nRF24L01 is a Transceiver Module, you can transmit and receive data using only one nRF24L01 Transceiver Module at one end of the communication.

So, in this project, I will implement two circuits using the nRF24L01 Transceiver Module. In the first circuit, I will show you how to enable Wireless Communication between two Arduino Boards using two nRF24L01 Transceiver Modules, in which one Arduino – nRF24L01 Transceiver Module pair acts as a Transmitter while the other Arduino – nRF24L01 Transceiver Module pair acts as a receiver.

Coming to the second circuit, I will make use of the Transceiver option of the nRF24L01 Transceiver Module and implement both the Arduino – nRF24L01 Transceiver Module pairs as both Transmitter and Receiver.

But there is one important thing you need to do before proceeding with the Arduino nRF24L01 Transceiver Module interface.

nRF24L01 Transceiver Module Adapter

If you notice the nRF24L01 Transceiver Module, the pins are not breadboard friendly and connecting wires directly will not be an ideal setup.

To overcome this, you have two options. First one is to make a small perf board for inserting the nRF24L01 Transceiver Module on top and with breadboard friendly pins at the bottom.

The second option is to buy an adapter for the nRF24L01 Transceiver Module as shown in the following image.

nRF24L01 Transceiver Module Adapter

As you can see, the adapter for nRF24L01 Transceiver Module consists of female headers for inserting the nRF24L01 Transceiver Module and corresponding male headers for connection with other boards like Arduino.

There is also a 3.3V regulator IC on the nRF24L01 Transceiver Module adapter so that you can provide 5V to the adapter (only to the adapter with 3.3V regulator and not directly to the nRF24L01 Transceiver Module itself).

Components Required

  • Arduino UNO x 2
  • nRF24L01 Transceiver Modules x 2
  • Joystick
  • TowerPro SG90 Servo Motor
  • LED
  • Push Button
  • 1KΩ Resistor

Simple Arduino Wireless Communication using nRF24L01 Transceiver Module

Circuit Diagram

nRF24L01 Transceiver Module Basic Wireless Communication Circuit Diagram


The following is the connections made between the Arduino UNO and nRF24L01 Modules at the Transmitter end.

nRF24L01 —— Arduino

VCC —– 3.3V


MOSI —– 11

MISO —– 12

SCK —– 13

CE —– 9

CSN —– 10

As I have used an Arduino UNO even at the receiver end, I have used the same connection. If you are using other Arduino Boards like Mega, check for the SPI Pins.


Transmitter Code


/* Transmitter */
#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>
RF24 radio(9, 10); // CE, CSN Pins
const uint64_t address = 0xF0F0F0F0E1LL;
void setup()
void loop()
const char sendData[] = This is a test!;
radio.write(&sendData, sizeof(sendData));


Receiver Code


/* Receiver */
#include <SPI.h>
#include <nRF24L01.h>
#include <RF24.h>
RF24 radio(9, 10); // CE, CSN Pins
const uint64_t address = 0xF0F0F0F0E1LL;
void setup()
radio.openReadingPipe(1, address);
void loop()
if (radio.available()) {
char recvData[32] = ;, sizeof(recvData));


NOTE: Bidirectional Wireless Communication Between Two Arduino Boards will be updated soon.


Similar Articles & Blogs

Explore similar articles on various electronics and electrical topics – 


We saw in the previous tutorial about the binary weighted digital-to-analogue converter that the analogue output voltage is the weighted sum of the individual inputs, and that

Learn More >>

Analogue to Digital Converter

Analogue-to-Digital Converters, (ADCs) allow micro-processor controlled circuits, Arduinos, Raspberry Pi, and other such digital logic circuits to communicate with the real world. In the real

Learn More >>

Transmission Gate

The analogue switch is a solid-state semiconductor switch that controls the transmission path of analogue signals. The open and closed operations of the switch positions

Learn More >>

Binary Adder

Another common and very useful combinational logic circuit which can be constructed using just a few basic logic gates allowing it to add together two

Learn More >>

Bus Transceiver

A Transceiver can be used to provide bidirectional, input or output control, of either digital or analogue devices to a common shared data bus. Unlike the buffer,

Learn More >>

Digital Comparator

Digital or Binary Comparators are made up from standard AND, NOR and NOT gates that compare the digital signals present at their input terminals and produce an output depending upon

Learn More >>